---

<<<<< On The Topic of 450 Baud! >>>>> by Scott Loftesness May 28, 1983 Many users have asked about using 450 baud with this RBBS system. Typically, they are asking why such an option exists (the N option on the main RBBS menu) when their modem and IBM-PC BASIC don't appear to support such a speed. They are correct about IBM-PC BASIC not supporting 450 baud. In fact, the ROM BIOS routines in the PC don't support 450 baud as an option either. It's not that IBM or Microsoft skipped the speed when they developed the PC, but the fact that 450 baud is not a standard communications speed for the RS-232-C interface. The next higher 'standard' speed above 300 baud is 600 baud, followed by 1200 baud, etc. As a result, 450 baud is not supported on most personal computer systems. As it turns out, however, most 300 baud modems will run at somewhat higher speeds - up to, guess what!, 450 baud in most cases. Although a somewhat higher error rate can be expected when you "push" a 300 baud modem to 450 baud, the error rate is typically still low enough to not be any kind of serious problem to file transfer and message passing operations. In fact, using the XMODEM file transfer protocol, errors which do occur are normally detected by the check sum error detection scheme used by XMODEM and simply force a re-transmission of the block originally received in error. Since the speed advantage of 450 over 300 baud can be substantial, and since we are all interested in doing the most work in the least amount of time with the equipment at hand, many users have implemented 450 baud as an option which can used with their "home-grown" communications programs. (Note that standard IBM-PC communications packages don't support 450 baud either - such as PC-Talk III). I'll describe how 450 baud can be implemented from a programming standpoint shortly. But first, let's get rid of a few erroneous impressions about modem operation. Your Hayes 300 baud SmartModem (or a Hayes 1200 running in 300 baud mode) is capable of receiving modem commands and data at up to 1200 baud. What this means is that the microprocessor in the Hayes is programmed to automatically look for the AT command sequence - and performs automatic baud rate detection at the speed you happen to be sending the command sequence to the modem. This capability, for example, is used in the RBBS code to send the various modem commands at 1200 baud - to minimize the time spent sending them! Your Hayes 300 will even try to send data across the line at 1200 baud - if you open your communications line at that speed and attempt to go to data mode. However, the 300 is not capable of handling data at that speed - in fact, it can only transmit and receive data at up to slightly more than 450 baud - with any reasonable error rate. Since the Hayes doesn't care at what rate is receives data (anything from 1 to 1200 baud is acceptable), it is possible to transmit data to the modem and have the modem transmit it to the phone line at any of those speeds. However, 450 baud is the reasonable upper limit for data communications with the Hayes 300. Now that we understand the workings of the Hayes modem, let's talk about how we can get the PC to send data from its RS-232-C Asynchronous Communications Adapter at 450 baud. As mentioned earlier, 450 is not an acceptable option to either the BASIC OPEN statement or to the direct BIOS calls for asychronous communications. However, as always, almost *anything* is possible using software! The IBM ACA uses an 8250 chip which is capable of running at speeds from 1 to 19,600 baud (officially, only up to 9600 baud, but that's another discussion!). The 8250 includes an on-chip software programmable baud rate generator - which actually determines the speed used to send and receive data across the RS-232-C interface. This baud rate generator can be programmed to run at *any* baud rate between 1 and 19,600 baud. The IBM-PC ROM BIOS routines, however, were programmed to only support the "standard" RS-232-C speeds. Since BASIC uses the BIOS routines, BASIC only supports those same "standard" speeds. However, it is possible for you to program the 8250 to run at any speed you like. In this case, we are only interested in programming it to run at 450 baud. Programming the baud rate generator in the 8250 consists of loading the baud rate generator on the chip with a "baud rate divisor" - which takes the clock frequency and divides it by the number you provide to come up with the baud rate itself. (Those of you with Technical Reference manuals for the PC can read all about this on pages 2-135 to 2-137). The divisor is a two byte value - which is stored into two one byte registers within the 8250 chip. First, we need to determine what the baud rate divisor should be for 450 baud operation. Take it from me that the value is X'0100'. Next, we need to get this value from a BASIC program into the 8250 itself. Fortunately, BASIC includes the OUT statement - which allows us to send data to the various I/O ports on the system. The 8250 uses several of these ports - for the baud rate divisior, modem control, and for actually sending and receiving the data across the RS-232-C interface. The baud rate divisor ports are X'3F8' for the least significant byte and X'3F9' for the most significant byte - when using the COM1 port. (COM2 addresses are X'2F8' and X'2F9' respectively. Before we can load these divisor ports, however, we must load another value to another port to indicate that we are setting the baud rate divisor. This third port is the Line Control Register and is port X'3FB' (X'2FB' for COM2). The high order bit (X'80') of the LCR controls access to the baud rate divisor registers. When this bit is 1, we can load the baud rate divisors. When it is 0, the 8250 resumes operation with the baud rate loaded. The following sequence of BASIC statements will load the baud rate divisor registers: OUT &H3FB,(INP(&H3FB) AND &H80) 'Enable divisor registers. OUT &H3F8,0 'Low order byte of X'0100' OUT &H3F9,1 'High order byte of X'0100' OUT &H3FB,(INP(&H3FB) OR &H80) 'Disable divisor registers. Adding this code to a BASIC program will cause the COM1 port to immediately switch to 450 baud operation. Switching to other speeds is just as easy. The only thing you need to know is the baud rate divisor required for that speed. Here are a few of the common divisors (see the full table in the Tech. Ref.): 300 X'0180' 450 X'0100' 1200 X'0060' I hope this discussion has helped to clarify the subject of 450 baud operation. Perhaps with this help, you can make some simple changes to whatever communications program you're running which will allow you to use your Hayes 300 at a speed which will allow up to 50 per cent faster communications!

---

The views and opinions stated within this web page are those of the author or authors which wrote them and may not reflect the views and opinions of the ISP or account user which hosts the web page. The opinions may or may not be those of the Chairman of The Skeptic Tank.

Return to The Skeptic Tank's main Index page.

E-Mail Fredric L. Rice / The Skeptic Tank